Category: PU Technology

HDI Low Viscosity Covesro XP2840

 

Characterization :

Aliphatic polyisocyanate based on hexamethylene diisocyanate.

As the hardener component for lightfast, weather-stable coating systems.

Form supplied :100 %

Characteristic data*

Property	Value	Unit of measurement	Method
NCO content	approx. 23.0	%	DIN EN ISO 11 909
Viscosity at 23 °C	approx. 500	mPa·s	DIN EN ISO 3219/A.3
Color value (Hazen)	< 80		DIN EN 1557
Monomeric HDI	≤ 0.26	%	DIN 55 956

*These values are provisional. Binding supply specifications will no be available until the final product data sheet is published.

Other data**：

Property	Value	Unit of measurement	Method
Viscosity at 25 °C	approx. 450	mPa·s	DIN EN ISO 3219/A.3
Equivalent weight	approx. 183	g
Flash point	183	°C	DIN EN 22 719
Density at 20 °C	1.15	g/cm3	DIN EN ISO 2811

**These values provide general information.

Solubility / thinnability ：

The product is compatible with the following solvents:

ethyl acetate, butyl acetate, 1-methoxypropylacetate-2, acetone, methyl ethyl ketone, methyl isobutyl ketone, cyclohexanone, toluene, xylene,solvent naphtha® 100 and mixtures thereof.

Aliphatic hydrocarbons are unsuitable as solvents.

Desmodur® XP 2840 should not be thinned to below a solids content of 40 % by weight. Prolonged storage of a solution with lower binder content may result in turbidity and sedimentation. Storage stability of the thinned product should be tested in each case.

 

Compatibility ：

Desmodur®XP 2840 can be blended with most Desmodur® grades, such as:Desmodur®N 75, N 100, N 3200, N 3300, N 3390, N 3400, N 3600, N 3900,Z 4470, HL and IL. Compatibility is generally good with hydroxyfunctional polyesters and polyethers (Desmophen®grades) as well as hydroxy acrylates.

It is incompatible with Desmophen® 650 and 651.

 

Properties / Applications ：

As a particularly low-viscosity polyisocyanate, Desmodur® XP 2840 is particularly well suited for the formulation of high-solids coatings for general industrial coating, automotive refinishing, transportation and plastics coating applications.

Storage：

– Storage in original sealed Covestro container.

– Recommended storage temperature: > 0 – 30 °C.

– Protect from moisture, heat and foreign material.

General information : The product is sensitive to moisture. Storage at higher temperatures will result in increase of color and viscosity.

Storage time ：

Covestro represents that, for a period of nine months following the day of shipment as stated in the respective transport documents, the product will meet the specifications or values set forth in section “specifications or characteristic data” above, what ever is applicable, provided that the product is stored in full compliance with the storage conditions set forth in and referenced under section “storage” above and is otherwise handled appropriately.

The lapse of the nine months period does not necessarily mean that the product no longer meets specifications or the set values. However, prior to using said product, Covestro recommends to test such a product if it still meets the specifications or the set values. Covestro does not make any representation regarding the product after the lapse of the nine months period and Covestro shall not be responsible or liable in any way for the product failing to meet specifications or the set values after the lapse of the nine months period.

E_mail us : [email protected]

HDI Low Viscosity Covesro XP2860

 

Characterization : 

Aliphatic polyisocyanate based on hexamethylene diisocyanate.

As the hardener component for lightfast, weather-stable coating systems.

Form supplied:100 %

 

Characteristic data*:

Property	Value	Unit of measurement	Method
NCO content	approx. 20.0	%	M105-ISO 11909
Viscosity at 23 °C	approx. 500	mPa·s	M014-ISO 3219/A.3
Color value (Hazen)	≤ 80		M017-EN 1557
Monomeric HDI	≤ 0.16	%	M106-ISO 10283

*These values are provisional. Binding supply specifications will not be available until the final product data sheet is published.

Other data**:

Property	Value	Unit of measurement	Method
Viscosity at 25 °C	approx. 450	mPa·s	DIN EN ISO 3219/A.3
Equivalent weight	approx. 215
Flash point	193	°C	DIN EN 22 719
Density at 20 °C	1.106	g/cm3	DIN EN ISO 2811

**These values provide general information.

 

Solubility / thinnability :

The product is compatible with the following solvents: ethyl acetate,butyl acetate, 1-methoxypropylacetate-2, acetone, methyl ethyl ketone, methyl isobutyl ketone, cyclohexanone, toluene, xylene, solvent naphtha®  100 and mixtures thereof.

Aliphatic hydrocarbons are unsuitable as solvents.

Desmodur®  XP 2860 should not be thinned to below a solids content of 40 % by weight. Prolonged storage of a solution with lowerbindercontent may result in turbidity and sedimentation. Storage stability of the thinned product should be tested in each case.

Compatibility :

Desmodur®  XP 2860 can be blended with most Desmodur® grades,such as: Desmodur® N 75, N 100, N 3200, N 3300, N 3390, N 3400, N 3600, N 3900, Z 4470, HL and IL. Compatibility is generally good with hydroxyfunctional polyesters and polyethers (Desmophen® grades) as well as hydroxy acrylates.

Properties / Applications :

As a particularly low-viscosity polyisocyanate, Desmodur®   XP  2860 is particularly well suited for the formulation of high-solids coatings for general industrial coating, automotive refinishing, transportation and plastics coating applications.

Storage :

– Storage in original sealed Covestro container.

– Recommended storage temperature: > 0 – 30 °C.

– Protect from moisture, heat and foreign material.

General information : The product is sensitive to moisture. Storag at higher temperatures will result in increase of color and viscosity.

Storage time :

Covestro represents that, for a period of nine months following the day of shipment as stated in the respective transport documents,the product will meet the specifications or values set forth in section “specifications or characteristic data” above, what ever is applicable, provided that the product is stored in full compliance with the storage conditions set forth in and referenced under section “storage” above and is otherwise handled appropriately. The lapse of the nine months period does not necessarily mean that the product no longer meetsspecifications or the set values. However, prior to using said product, Covestro recommends to test such a product if it still meets the specifications or the set values. Covestro does not make any representation regarding the product after the lapse of the nine months period and Covestro shall not be responsible or liable in any way for the product failing to meet specifications or the set values after the lapse of the nine months period.

Labeling and statutory requirements ：

This product data sheet is only valid in conjunction with the latestedition of the corresponding Safety Data Sheet. Any updating of safety-relevant information – in accordance with statutory requirements – will only be reflected in the Safety Data Sheet, copies of which will be revised and distributed. Information relating to the current classification and labeling, applications and processing methods and further data relevant to safety can be found in the currently valid Safety Data Sheet.

 

Further information :

The product is used mainly as a hardener in coating materials or adhesives. The handling of coating materials or adhesives containing reactive polyisocyanates and residual monomeric HDI requires appropriate protective measures referred to in the safety data sheet. These products may therefore be used only in industrial or trade applications. They are not suitable for use in homeworker (DIY) applications.

Important :

This is a Trial Product of which we do not yet have extensive experience. No guarantee can therefore be given regarding the behaviour of the product during processing or use.

E_mail us : [email protected]

HDI Low Viscosity Covesro XP2580

 

Characterization :

Desmodur XP 2580 is an aliphatic polyisocyanate based on hexamethylene diisocyanate (HDI).

It is suitable for use as the hardener component for lightfast, weather-stable coating systems.

Form supplied :Form supplied is 100%.

Characteristic data:

Property	Value	Unit of measurement	Method
NCO content	19.5 ± 0.5 %	%
Viscosity at 25°C	450 ± 150	mPa∙s
Hazen color value	≤ 80
Monomeric HDI	≤ 0.14	%

Other data*:

Property	Value	Unit of measurement
Viscosity at 23°C	approx. 500	mPa∙s
Equivalent weight	approx. 215
Flash point	193	°C
Density at 20°C	1.106	g/cm3
Solids	approx. 99.8	wt.-%
Weight per gallon	9.3	lb.

*These values provide general information and are not part of the product specification.

Solubility / thinnability:

The product is compatible with the following solvents: ethyl acetate, butyl acetate, 1-methoxypropylacetate-2, acetone, methyl ethyl ketone, methyl isobutyl ketone, cyclohexanone, toluene, xylene, solvent naphtha 100 and mixtures thereof.

Aliphatic hydrocarbons are unsuitable as solvents.

Desmodur XP 2580 should not be thinned to below a solids content of 40% by weight. Prolonged storage of a solution with lower binder content may result in turbidity and sedimentation. Storage stability of the thinned product should be tested in each case.

 

Compatibility:

Desmodur XP 2580 can be blended with most Desmodur grades, such as: Desmodur® N 75, N 100, N 3200, N 3300, N 3390, N 3400, N 3600, Desmodur N 3900, Z 4470, HL and IL. Compatibility is generally good with hydroxyfunctional polyesters and polyethers (Desmophen® grades) as well as hydroxy acrylates.

 

Properties / Applications :

As a particularly low-viscosity polyisocyanate, Desmodur XP 2580 is

particularly well suited for the formulation of high-solids coatings for general industrial coating, automotive refinishing, transportation and plastics coating applications.

As with any product, use of Desmodur XP 2580 in a given application must be tested (including but not limited to field testing) in advance by the user to determine suitability.

Handling information:

This product contains reactive HDI polyisocyanate/prepolymer and/or

monomeric HDI and should only be handled using appropriate protective

measures. Please review this product’s Safety Data Sheet for a summary of such protective measures. These products are suitable only for and should only be sold for use by industrial or trade (commercial) professionals. These products are not suitable for Do-It-Yourself applications.

Storage :

Desmodur XP 2580 should be stored in tightly sealed original containers and protected from moisture, heat, and foreign materials. The product is sensitive to moisture. Storage at higher temperatures will result in increase of color and viscosity. Recommended storage temperature is 5º-30ºC.

 

Storage time:

Desmodur XP 2580 has a shelf life of six months from date of receipt at

customer, provided the material is stored in sealed original containers at the recommended storage temperature.

Other Information :

Desmodur® and Desmophen®are registered trademarks of Covestro.

 

Health and Safety Information:

Appropriate literature has been assembled which provides information

concerning the health and safety precautions that must be observed when

handling this product. Before working with this product, you must read

and become familiar with the available information on its risks, proper

use, and handling. This cannot be overemphasized. Information is available in several forms, e.g., safety data sheets and product labels. For further information contact your Covestro LLC representative or the Product Safety and Regulatory Affairs Department in Pittsburgh, PA.

E_mail us : [email protected]