Author: admin
soft foam amine catalyst NE300/Dabco foaming catalyst
soft foam amine catalyst NE300/Dabco foaming catalyst
Overview:
Product Name: Dabco NE300
Alias: N,N,N’-Trimethyl-N’-3-aminopropyl-bis(aminoethyl) ether, Dabco NE300, Amine catalyst for flexible molded foam NE300, Dabco foaming catalyst, Polyurethane foaming catalyst NE300
Product Description: Dabco NE300 non-volatile catalyst for flexible molded foam, N,N,N’-trimethyl-N’-3-aminopropyl-bis(aminoethyl) ether
Product Physical Properties:
Appearance: colorless liquid
Viscosity(25℃,mPa.s):9.2
Density(25℃,g/cm3):0.91
Water solubility: soluble in water
Flash point (PMCC,℃): 124
Hydroxyl value (mgKOH/g): 276
Brief introduction.
Dabco NE300 catalyst is a third generation non-emission (NE series) polyurethane foaming catalyst.The foam properties of Dabco NE300 catalyst chemically bonded to polyurethane foams in MDI or TDI systems solves the problems of odors and emissions associated with polyurethane catalysts used in the automotive industry that can cause windshield fogging and vinyl staining. Vinyl Staining.
Dabco NE300 catalyst can be used in conjunction with other non-volatile catalysts (e.g., Dabco NE1070) or with conventional volatile catalysts to reduce emissions and odors.
Dynamic headspace analysis by OEM VDA 278 method showed no emissions from the Dabco NE300 catalyst. These results demonstrate that the Dabco NE300 catalyst is fully bound to the foam. Vapor pressure measurements show that the volatility of Dabco NE300 non-volatile catalyst is significantly lower than current industry standards, which means that the catalyst in the foam line operates at a lower level of volatility.
Typical Physical Properties Table.
Appearance Light yellow transparent liquid
Specific Gravity 0.89
Viscosity @25°C mPa.s 9.2
Solubility in water @ 25°C Fully soluble
Flash point, ℃ 124
Characteristics
Non-volatile polyurethane foaming catalyst
No VOC emission
No vinyl staining
No windshield fogging
Stabilized masterbatch
Recommendations for Use.
Dabco NE300 Catalyst is recommended for use in any water-blown TDI or TDI/MDI polyurethane high resilient (HR) foam; and TDI/MDI or MDI-based cold-cured polyurethane foamed molding mat systems.Dabco NE300 Non-Volatile Catalyst is compatible with other commonly used polyurethane catalysts and additives and is miscible with polyols and polyol/water mixtures.
The recommended dosage of Dabco NE300 catalyst is 0.1-0.2pphp in MDI systems and 0.15-0.2pphp in TDI systems.
Product Usage:
Dabco NE300 is a non-emitting amine catalyst used to promote urea (water-isocyanate) reactions. It reacts into the polyurethane matrix and therefore produces no organic volatiles;
Dabco NE300 is suitable for all molded foam and high density foam applications to meet OEM emission regulations such as VDA278;
Dabco NE300 is also used in flexible block foam (polyether and polyester) applications to meet Certipur or LGA requirements;
Dabco NE300 is a non-emitting catalyst that replaces Dabco BL-11 catalyst;
Dabco NE300 can be used in any water-blown TDI or TDI/MDI high resilient (HR) foam as well as TDI/MDI or MDI-type cold cure molded polyurethane foam;
Dabco NE300 is recommended for use at 0.50-1 PPHP (per one hundred parts of polyol) in MDI systems and 0.4-0.7 PPHP in TDI systems.
Shelf Life.
Keep unopened for two years
Storage and Transportation:
Should be sealed and stored in a dry, cool and ventilated warehouse
Packaging:
200KG/drum Storage: it is recommended to store in dry and cool area with proper ventilation. Please fasten the packaging cover as soon as possible after the original packaging to prevent the mixing of other substances such as moisture and other substances that may affect the product performance. Store in a cool and dry place, keep the container sealed and avoid contact with oxides. Do not inhale dust and avoid contact with skin and mucous membranes. Smoking, eating and drinking are prohibited in the workplace. After work, shower and change clothes. Store contaminated clothing separately and wash before use. Maintain good hygiene practices. The company recommends that all polyurethane catalysts be stored in a dry, cool and properly ventilated area. All storage containers must be well sealed to avoid contact with water or other affected substances, which may alter the performance of the product in use. The storage temperature is 10°C to 30°C. Lower or higher temperatures are inappropriate and should be avoided if possible.
Dabco foaming catalyst/polyurethane foaming catalyst NE300
Dabco foaming catalyst/polyurethane foaming catalyst NE300
Overview:
Product Name: Dabco NE300
Alias: N,N,N’-Trimethyl-N’-3-aminopropyl-bis(aminoethyl) ether, Dabco NE300, Amine catalyst for flexible molded foam NE300, Dabco foaming catalyst, Polyurethane foaming catalyst NE300
Product Description: Dabco NE300 non-volatile catalyst for flexible molded foam, N,N,N’-trimethyl-N’-3-aminopropyl-bis(aminoethyl) ether
Product Physical Properties:
Appearance: colorless liquid
Viscosity(25℃,mPa.s):9.2
Density(25℃,g/cm3):0.91
Water solubility: soluble in water
Flash point (PMCC,℃): 124
Hydroxyl value (mgKOH/g): 276
Brief introduction.
Dabco NE300 catalyst is a third generation non-emission (NE series) polyurethane foaming catalyst.The foam properties of Dabco NE300 catalyst chemically bonded to polyurethane foams in MDI or TDI systems solves the problems of odors and emissions associated with polyurethane catalysts used in the automotive industry that can cause windshield fogging and vinyl staining. Vinyl Staining.
Dabco NE300 catalyst can be used in conjunction with other non-volatile catalysts (e.g., Dabco NE1070) or with conventional volatile catalysts to reduce emissions and odors.
Dynamic headspace analysis by OEM VDA 278 method showed no emissions from the Dabco NE300 catalyst. These results demonstrate that the Dabco NE300 catalyst is fully bound to the foam. Vapor pressure measurements show that the volatility of Dabco NE300 non-volatile catalyst is significantly lower than current industry standards, which means that the catalyst in the foam line operates at a lower level of volatility.
Typical Physical Properties Table.
Appearance Light yellow transparent liquid
Specific Gravity 0.89
Viscosity @25°C mPa.s 9.2
Solubility in water @ 25°C Fully soluble
Flash point, ℃ 124
Characteristics
Non-volatile polyurethane foaming catalyst
No VOC emission
No vinyl staining
No windshield fogging
Stabilized masterbatch
Recommendations for Use.
Dabco NE300 Catalyst is recommended for use in any water-blown TDI or TDI/MDI polyurethane high resilient (HR) foam; and TDI/MDI or MDI-based cold-cured polyurethane foamed molding mat systems.Dabco NE300 Non-Volatile Catalyst is compatible with other commonly used polyurethane catalysts and additives and is miscible with polyols and polyol/water mixtures.
The recommended dosage of Dabco NE300 catalyst is 0.1-0.2pphp in MDI systems and 0.15-0.2pphp in TDI systems.
Product Usage:
Dabco NE300 is a non-emitting amine catalyst used to promote urea (water-isocyanate) reactions. It reacts into the polyurethane matrix and therefore produces no organic volatiles;
Dabco NE300 is suitable for all molded foam and high density foam applications to meet OEM emission regulations such as VDA278;
Dabco NE300 is also used in flexible block foam (polyether and polyester) applications to meet Certipur or LGA requirements;
Dabco NE300 is a non-emitting catalyst that replaces Dabco BL-11 catalyst;
Dabco NE300 can be used in any water-blown TDI or TDI/MDI high resilient (HR) foam as well as TDI/MDI or MDI-type cold cure molded polyurethane foam;
Dabco NE300 is recommended for use at 0.50-1 PPHP (per one hundred parts of polyol) in MDI systems and 0.4-0.7 PPHP in TDI systems.
Shelf Life.
Keep unopened for two years
Storage and Transportation:
Should be sealed and stored in a dry, cool and ventilated warehouse
Packaging:
200KG/drum Storage: it is recommended to store in dry and cool area with proper ventilation. Please fasten the packaging cover as soon as possible after the original packaging to prevent the mixing of other substances such as moisture and other substances that may affect the product performance. Store in a cool and dry place, keep the container sealed and avoid contact with oxides. Do not inhale dust and avoid contact with skin and mucous membranes. Smoking, eating and drinking are prohibited in the workplace. After work, shower and change clothes. Store contaminated clothing separately and wash before use. Maintain good hygiene practices. The company recommends that all polyurethane catalysts be stored in a dry, cool and properly ventilated area. All storage containers must be well sealed to avoid contact with water or other affected substances, which may alter the performance of the product in use. The storage temperature is 10°C to 30°C. Lower or higher temperatures are inappropriate and should be avoided if possible.
Dabco NE500/non-emission amine catalyst NE500
Dabco NE500/non-emission amine catalyst NE500
Overview:
Product Name: Dabco NE500
Alias: Dabco NE500, Non-emitting Amine Catalyst NE500, Strong Gel Amine Catalyst NE500, Dabco Strong Gel Amine Catalyst
Product Description: Dabco NE500 non-emitting catalyst for polyurethane block foams
Product Physical Properties:
Appearance: colorless liquid
Viscosity(25℃,mPa.s):1500
Density (25℃,g/cm3): 1.04
Water solubility: soluble in water
Flash point (PMCC,℃): >200
Hydroxyl value (mgKOH/g): 280
Brief introduction.
Dabco NE500 catalyst is a non-emissive tertiary amine used as a catalyst for polyurethane block sponges to promote urethane reactions.Dabco NE500 catalyst has reactive functional groups that react with the polyurethane matrix and therefore do not cause emissions.
Dabco NE500 catalyst is used in soft bulk sponge applications to meet the required specifications of Certipur or LGA. For polyurethane applications requiring low VOC and low emissions, Dabco NE500 catalyst is an alternative to DABCO 33-LV catalyst for non-emission needs.
Typical Physical Properties Table.
Appearance Colorless Clear Liquid
Specific Gravity 1.04
Viscosity @ 25°C mPa.s 1500
Water solubility @ 25°C soluble
Flash point, ℃ ＞200
Characteristics
Promote urethane (polyol-isocyanate) reaction
Non-emitting amine catalyst
Improves foam flow, can replace Dabco 33-LV catalysts
Reduces odor and VOC
Recommendations for Use.
Dabco NE500 catalyst is recommended for use in water-blown, methylene chloride (MC) or other alternative blowing agent block polyurethane foam systems. Dabco NE500 Catalyst is compatible with other commonly used polyurethane catalysts and additives and is readily miscible with polyols and polyol/water mixtures.
Product Usage:
Dabco NE500 is a non-emitting amine catalyst used to promote urea (water-isocyanate) reactions. It reacts into the polyurethane matrix so that no organic volatiles are generated;
Dabco NE500 is also used in flexible block foam (polyether and polyester) applications to meet Certipur or LGA requirements;
Dabco NE500 is a non-emitting catalyst that improves foam flow and can be used as a replacement for Dabco 33-LV catalyst;
Dabco NE500 can be used in any water-blown, methylene chloride-blown, etc. polyurethane block foam system.
Shelf Life.
Keep unopened for two years
Storage and Transportation:
Should be kept sealed and stored in a dry, cool and ventilated warehouse
Packing:
200KG/drum Storage: it is recommended to store in dry and cool area with proper ventilation. Please fasten the packaging cover as soon as possible after the original packaging to prevent the mixing of other substances such as moisture and other substances that may affect the product performance. Store in a cool and dry place, keep the container sealed and avoid contact with oxides. Do not inhale dust and avoid contact with skin and mucous membranes. Smoking, eating and drinking are prohibited in the workplace. After work, shower and change clothes. Store contaminated clothing separately and wash before use. Maintain good hygiene practices. The company recommends that all polyurethane catalysts be stored in a dry, cool and properly ventilated area. All storage containers must be well sealed to avoid contact with water or other affected substances, which may alter the performance of the product in use. The storage temperature is 10°C to 30°C. Lower or higher temperatures are inappropriate and should be avoided if possible.
Company Name: |
Newtop Chemical Materials (Shanghai) Co., Ltd. |
Sales Manager: |
Hunter |
E_Mail: |
[email protected] |
Telephone: |
86-021-5657 7831 |
Fax: |
86-021-5657 7830 |
Address: |
Rm. 1104, No. 258, Songxing West Road,
|
Website: |
www.newtopchem.com |
strong gel amine catalyst NE500/Dabco strong gel amine catalyst
strong gel amine catalyst NE500/Dabco strong gel amine catalyst
Overview:
Product Name: Dabco NE500
Alias: Dabco NE500, Non-emitting Amine Catalyst NE500, Strong Gel Amine Catalyst NE500, Dabco Strong Gel Amine Catalyst
Product Description: Dabco NE500 non-emitting catalyst for polyurethane block foams
Product Physical Properties:
Appearance: colorless liquid
Viscosity(25℃,mPa.s):1500
Density (25℃,g/cm3): 1.04
Water solubility: soluble in water
Flash point (PMCC,℃): >200
Hydroxyl value (mgKOH/g): 280
Brief introduction.
Dabco NE500 catalyst is a non-emissive tertiary amine used as a catalyst for polyurethane block sponges to promote urethane reactions.Dabco NE500 catalyst has reactive functional groups that react with the polyurethane matrix and therefore do not cause emissions.
Dabco NE500 catalyst is used in soft bulk sponge applications to meet the required specifications of Certipur or LGA. For polyurethane applications requiring low VOC and low emissions, Dabco NE500 catalyst is an alternative to DABCO 33-LV catalyst for non-emission needs.
Typical Physical Properties Table.
Appearance Colorless Clear Liquid
Specific Gravity 1.04
Viscosity @ 25°C mPa.s 1500
Water solubility @ 25°C soluble
Flash point, ℃ ＞200
Characteristics
Promote urethane (polyol-isocyanate) reaction
Non-emitting amine catalyst
Improves foam flow, can replace Dabco 33-LV catalysts
Reduces odor and VOC
Recommendations for Use.
Dabco NE500 catalyst is recommended for use in water-blown, methylene chloride (MC) or other alternative blowing agent block polyurethane foam systems. Dabco NE500 Catalyst is compatible with other commonly used polyurethane catalysts and additives and is readily miscible with polyols and polyol/water mixtures.
Product Usage:
Dabco NE500 is a non-emitting amine catalyst used to promote urea (water-isocyanate) reactions. It reacts into the polyurethane matrix so that no organic volatiles are generated;
Dabco NE500 is also used in flexible block foam (polyether and polyester) applications to meet Certipur or LGA requirements;
Dabco NE500 is a non-emitting catalyst that improves foam flow and can be used as a replacement for Dabco 33-LV catalyst;
Dabco NE500 can be used in any water-blown, methylene chloride-blown, etc. polyurethane block foam system.
Shelf Life.
Keep unopened for two years
Storage and Transportation:
Should be kept sealed and stored in a dry, cool and ventilated warehouse
Packing:
200KG/drum Storage: it is recommended to store in dry and cool area with proper ventilation. Please fasten the packaging cover as soon as possible after the original packaging to prevent the mixing of other substances such as moisture and other substances that may affect the product performance. Store in a cool and dry place, keep the container sealed and avoid contact with oxides. Do not inhale dust and avoid contact with skin and mucous membranes. Smoking, eating and drinking are prohibited in the workplace. After work, shower and change clothes. Store contaminated clothing separately and wash before use. Maintain good hygiene practices. The company recommends that all polyurethane catalysts be stored in a dry, cool and properly ventilated area. All storage containers must be well sealed to avoid contact with water or other affected substances, which may alter the performance of the product in use. The storage temperature is 10°C to 30°C. Lower or higher temperatures are inappropriate and should be avoided if possible.
Company Name: |
Newtop Chemical Materials (Shanghai) Co., Ltd. |
Sales Manager: |
Hunter |
E_Mail: |
[email protected] |
Telephone: |
86-021-5657 7831 |
Fax: |
86-021-5657 7830 |
Address: |
Rm. 1104, No. 258, Songxing West Road,
|
Website: |
www.newtopchem.com |
strong gel amine catalyst BX405/low odor amine catalyst BX405
strong gel amine catalyst BX405/low odor amine catalyst BX405
Overview:
Product Name: Dabco BX405
Alias: Dabco BX405, low odor strong gel amine catalyst BX405, strong gel amine catalyst BX405, low odor amine catalyst BX405, low odor strong gel catalyst BX405, Dabco BX405 polyurethane catalyst
Product description: low odor catalyst for polyurethane insulation DABCO BX405
Product Physical Properties:
Appearance: colorless liquid
Viscosity(25℃,mPa.s):13
Density (25℃,g/cm3): 0.914
Water solubility: completely soluble in water
Flash point (PMCC,℃): >100
Hydroxyl value (mgKOH/g): 327
Brief introduction.
DABCO BX405 catalyst is a highly efficient polyurethane amine catalyst that strongly catalyzes the reaction between polyol and isocyanate and promotes the formation of urethane esters, thus shortening the post-curing time of polyurethane foam.
DABCO BX405 catalyst offers better post-cure performance than POLYCAT 8 (dimethylcyclohexylamine DMCHA), with catalytic activity comparable to that of POLYCAT 8, as well as better mold release than POLYCAT 8, and flow and K-factor as good as POLYCAT 8. DABCO BX405 can be used in a wide range of rigid polyurethane foam applications DABCO BX405 can be used in various applications of rigid polyurethane foam, such as polyurethane pipe insulation, polyurethane insulation boards, and is particularly suitable for electrical refrigerator formulations.
Typical Physical Properties Table.
Appearance Colorless transparent liquid
Specific gravity 0.914
Viscosity @25℃ mPa.s 13
Water solubility @25℃ completely dissolved
Flash point, ℃ ＞100
Characteristics
Low odor hard foam catalyst, replacing dimethylcyclohexylamine DMCHA
Same fluidity and K-factor as POLYCAT 8.
Better mold release and post cure
Particularly suitable for refrigerator formulations
Suggestions for Use: Dabco BX405 Catalyst
Dabco BX405 catalyst is a low odor, strong gel catalyst that strongly catalyzes the reaction between polyols and isocyanates, resulting in a shorter post-cure time; Compared to dimethylcyclohexylamine DMCHA, Dabco BX405 catalyst has better mold release and post-cure properties, low odor, etc.; Dabco BX405 catalyst can be used in a wide range of polyurethane rigid foams.
Product Usage:
Dabco BX405 is a low-odor, strong-gelling amine catalyst that strongly catalyzes the reaction of polyols with isocyanates, thereby reducing post-cure time;
Compared with dimethylcyclohexylamine, Dabco BX405 has better mold release and post-cure properties, and low odor;
Dabco BX405 can be used in all kinds of polyurethane rigid foam, especially in appliances.
Shelf life.
Keep unopened for two years
Storage and transportation:
Should be kept sealed and stored in a dry, cool and ventilated warehouse
Packing:
200KG/drum Storage: it is recommended to store in dry and cool area with proper ventilation. Please fasten the packaging cover as soon as possible after the original packaging to prevent the mixing of other substances such as moisture and other substances that may affect the product performance. Store in a cool and dry place, keep the container sealed and avoid contact with oxides. Do not inhale dust and avoid contact with skin and mucous membranes. Smoking, eating and drinking are prohibited in the workplace. After work, shower and change clothes. Store contaminated clothing separately and wash before use. Maintain good hygiene practices. The company recommends that all polyurethane catalysts be stored in a dry, cool and properly ventilated area. All storage containers must be well sealed to avoid contact with water or other affected substances, which may alter the performance of the product in use. The storage temperature is 10°C to 30°C. Lower or higher temperatures are inappropriate and should be avoided if possible.
Company Name: |
Newtop Chemical Materials (Shanghai) Co., Ltd. |
Sales Manager: |
Hunter |
E_Mail: |
[email protected] |
Telephone: |
86-021-5657 7831 |
Fax: |
86-021-5657 7830 |
Address: |
Rm. 1104, No. 258, Songxing West Road,
|
Website: |
www.newtopchem.com |
low odor amine catalyst BX405/low odor strong gel catalyst BX405
low odor amine catalyst BX405/low odor strong gel catalyst BX405
Overview:
Product Name: Dabco BX405
Alias: Dabco BX405, low odor strong gel amine catalyst BX405, strong gel amine catalyst BX405, low odor amine catalyst BX405, low odor strong gel catalyst BX405, Dabco BX405 polyurethane catalyst
Product description: low odor catalyst for polyurethane insulation DABCO BX405
Product Physical Properties:
Appearance: colorless liquid
Viscosity(25℃,mPa.s):13
Density (25℃,g/cm3): 0.914
Water solubility: completely soluble in water
Flash point (PMCC,℃): >100
Hydroxyl value (mgKOH/g): 327
Brief introduction.
DABCO BX405 catalyst is a highly efficient polyurethane amine catalyst that strongly catalyzes the reaction between polyol and isocyanate and promotes the formation of urethane esters, thus shortening the post-curing time of polyurethane foam.
DABCO BX405 catalyst offers better post-cure performance than POLYCAT 8 (dimethylcyclohexylamine DMCHA), with catalytic activity comparable to that of POLYCAT 8, as well as better mold release than POLYCAT 8, and flow and K-factor as good as POLYCAT 8. DABCO BX405 can be used in a wide range of rigid polyurethane foam applications DABCO BX405 can be used in various applications of rigid polyurethane foam, such as polyurethane pipe insulation, polyurethane insulation boards, and is particularly suitable for electrical refrigerator formulations.
Typical Physical Properties Table.
Appearance Colorless transparent liquid
Specific gravity 0.914
Viscosity @25℃ mPa.s 13
Water solubility @25℃ completely dissolved
Flash point, ℃ ＞100
Characteristics
Low odor hard foam catalyst, replacing dimethylcyclohexylamine DMCHA
Same fluidity and K-factor as POLYCAT 8.
Better mold release and post cure
Particularly suitable for refrigerator formulations
Suggestions for Use: Dabco BX405 Catalyst
Dabco BX405 catalyst is a low odor, strong gel catalyst that strongly catalyzes the reaction between polyols and isocyanates, resulting in a shorter post-cure time; Compared to dimethylcyclohexylamine DMCHA, Dabco BX405 catalyst has better mold release and post-cure properties, low odor, etc.; Dabco BX405 catalyst can be used in a wide range of polyurethane rigid foams.
Product Usage:
Dabco BX405 is a low-odor, strong-gelling amine catalyst that strongly catalyzes the reaction of polyols with isocyanates, thereby reducing post-cure time;
Compared with dimethylcyclohexylamine, Dabco BX405 has better mold release and post-cure properties, and low odor;
Dabco BX405 can be used in all kinds of polyurethane rigid foam, especially in appliances.
Shelf life.
Keep unopened for two years
Storage and transportation:
Should be kept sealed and stored in a dry, cool and ventilated warehouse
Packing:
200KG/drum Storage: it is recommended to store in dry and cool area with proper ventilation. Please fasten the packaging cover as soon as possible after the original packaging to prevent the mixing of other substances such as moisture and other substances that may affect the product performance. Store in a cool and dry place, keep the container sealed and avoid contact with oxides. Do not inhale dust and avoid contact with skin and mucous membranes. Smoking, eating and drinking are prohibited in the workplace. After work, shower and change clothes. Store contaminated clothing separately and wash before use. Maintain good hygiene practices. The company recommends that all polyurethane catalysts be stored in a dry, cool and properly ventilated area. All storage containers must be well sealed to avoid contact with water or other affected substances, which may alter the performance of the product in use. The storage temperature is 10°C to 30°C. Lower or higher temperatures are inappropriate and should be avoided if possible.
Company Name: |
Newtop Chemical Materials (Shanghai) Co., Ltd. |
Sales Manager: |
Hunter |
E_Mail: |
[email protected] |
Telephone: |
86-021-5657 7831 |
Fax: |
86-021-5657 7830 |
Address: |
Rm. 1104, No. 258, Songxing West Road,
|
Website: |
www.newtopchem.com |
Dabco NE210/amine balance catalyst NE210
Dabco NE210/amine balance catalyst NE210
Overview:
Product Name: Dabco NE210
Alias: Dabco NE210, Amine Equilibrium Catalyst NE210, Equilibrium Catalyst NE210, Dabco Amine Catalyst, Non-Emitting Amine Catalyst, Amine Catalyst, Amine Equilibrium Catalyst
Product Description: Dabco NE210 is a solution of 30% ZF-10 and 70% NE1070.
Product Physical Properties:
Appearance: light yellow liquid
Viscosity (25℃,mPa.s): 320
Density (25℃,g/cm3): 1.03
Water solubility: soluble in water
Flash point (PMCC,℃): 134
Hydroxyl value (mgKOH/g): 620
Typical Physical Properties Table.
Appearance Colorless transparent liquid
Specific gravity 1.03
Viscosity@25℃ mPa.s 320
Water solubility @25°C Completely soluble
Flash point, ℃ 134
Product Usage:
Dabco NE210 is a non-emitting amine equilibrium catalyst that reacts into the polyurethane matrix and therefore produces no emissions;
Dabco NE210 is suitable for all molded foam and high density foam applications to meet OEM emission regulations such as VDA278;
Advantages of Dabco NE210 include: no amine catalyst emissions, no VOC emissions, no vinyl staining, no windshield fogging, and stable masterbatch;
Dabco NE210 can be used in any water-blown TDI or TDI/MDI high resilient foam (HR) as well as TDI/MDI or MDI-type cold cure molded polyurethane foam;
Dabco NE210 is recommended at a dosage of 0.50 to 1 PPHP (per hundred parts of polyol) in MDI systems and 0.40 to 0.70 PPHP in TDI systems.
DABCO NE210 polyurethane foaming catalyst is a new, second generation, non-emission (NE) foaming catalyst that chemically binds to the polyurethane foam matrix and maintains the foam properties of diphenylmethylene diisocyanate (MDI) or toluene diisocyanate (TDI) systems.
DABCO NE210 eliminates windshield fogging and polyethylene plastic contamination caused by odor and volatile emissions when used in automotive manufacturing. This catalyst can be used in combination with other non-volatile catalysts such as Dabco NE1070 or alone with conventional co-catalysts to reduce volatiles and odor emissions. The Dabco NE210 catalyst was shown to be free of volatile emissions by dynamic above surface gas analysis using standard automotive OEM VDA278 methodology. These results confirm that the catalyst is fully bonded to the foam matrix. Vapor pressure measurements show that the volatility of the catalyst is well below current industry standards, which means that catalyst processing in foam production lines is much less volatile.
Advantages of DABCO NE210:
-
No amine catalyst volatilization
2、No volatile organic compounds emission
3, no polyethylene plastic contamination
4, no windshield fog and water droplets
5, Batch-to-batch stability is guaranteed
Shelf life.
Keep unopened, two years
Storage and transportation:
Should be sealed and stored in a dry, cool and ventilated warehouse
Packaging:
200KG/drum Storage: it is recommended to store in dry and cool area with proper ventilation. Please fasten the packaging cover as soon as possible after the original packaging to prevent the mixing of other substances such as moisture and other substances that may affect the product performance. Store in a cool and dry place, keep the container sealed and avoid contact with oxides. Do not inhale dust and avoid contact with skin and mucous membranes. Smoking, eating and drinking are prohibited in the workplace. After work, shower and change clothes. Store contaminated clothing separately and wash before use. Maintain good hygiene practices. The company recommends that all polyurethane catalysts be stored in a dry, cool and properly ventilated area. All storage containers must be well sealed to avoid contact with water or other affected substances, which may alter the performance of the product in use. The storage temperature is 10°C to 30°C. Lower or higher temperatures are inappropriate and should be avoided if possible.
Company Name: |
Newtop Chemical Materials (Shanghai) Co., Ltd. |
Sales Manager: |
Hunter |
E_Mail: |
[email protected] |
Telephone: |
86-021-5657 7831 |
Fax: |
86-021-5657 7830 |
Address: |
Rm. 1104, No. 258, Songxing West Road,
|
Website: |
www.newtopchem.com |
balance catalyst NE210/Dabco amine catalyst
balance catalyst NE210/Dabco amine catalyst
Overview:
Product Name: Dabco NE210
Alias: Dabco NE210, Amine Equilibrium Catalyst NE210, Equilibrium Catalyst NE210, Dabco Amine Catalyst, Non-Emitting Amine Catalyst, Amine Catalyst, Amine Equilibrium Catalyst
Product Description: Dabco NE210 is a solution of 30% ZF-10 and 70% NE1070.
Product Physical Properties:
Appearance: light yellow liquid
Viscosity (25℃,mPa.s): 320
Density (25℃,g/cm3): 1.03
Water solubility: soluble in water
Flash point (PMCC,℃): 134
Hydroxyl value (mgKOH/g): 620
Typical Physical Properties Table.
Appearance Colorless transparent liquid
Specific gravity 1.03
Viscosity@25℃ mPa.s 320
Water solubility @25°C Completely soluble
Flash point, ℃ 134
Product Usage:
Dabco NE210 is a non-emitting amine equilibrium catalyst that reacts into the polyurethane matrix and therefore produces no emissions;
Dabco NE210 is suitable for all molded foam and high density foam applications to meet OEM emission regulations such as VDA278;
Advantages of Dabco NE210 include: no amine catalyst emissions, no VOC emissions, no vinyl staining, no windshield fogging, and stable masterbatch;
Dabco NE210 can be used in any water-blown TDI or TDI/MDI high resilient foam (HR) as well as TDI/MDI or MDI-type cold cure molded polyurethane foam;
Dabco NE210 is recommended at a dosage of 0.50 to 1 PPHP (per hundred parts of polyol) in MDI systems and 0.40 to 0.70 PPHP in TDI systems.
DABCO NE210 polyurethane foaming catalyst is a new, second generation, non-emission (NE) foaming catalyst that chemically binds to the polyurethane foam matrix and maintains the foam properties of diphenylmethylene diisocyanate (MDI) or toluene diisocyanate (TDI) systems.
DABCO NE210 eliminates windshield fogging and polyethylene plastic contamination caused by odor and volatile emissions when used in automotive manufacturing. This catalyst can be used in combination with other non-volatile catalysts such as Dabco NE1070 or alone with conventional co-catalysts to reduce volatiles and odor emissions. The Dabco NE210 catalyst was shown to be free of volatile emissions by dynamic above surface gas analysis using standard automotive OEM VDA278 methodology. These results confirm that the catalyst is fully bonded to the foam matrix. Vapor pressure measurements show that the volatility of the catalyst is well below current industry standards, which means that catalyst processing in foam production lines is much less volatile.
Advantages of DABCO NE210:
-
No amine catalyst volatilization
2、No volatile organic compounds emission
3, no polyethylene plastic contamination
4, no windshield fog and water droplets
5, Batch-to-batch stability is guaranteed
Shelf life.
Keep unopened, two years
Storage and transportation:
Should be sealed and stored in a dry, cool and ventilated warehouse
Packaging:
200KG/drum Storage: it is recommended to store in dry and cool area with proper ventilation. Please fasten the packaging cover as soon as possible after the original packaging to prevent the mixing of other substances such as moisture and other substances that may affect the product performance. Store in a cool and dry place, keep the container sealed and avoid contact with oxides. Do not inhale dust and avoid contact with skin and mucous membranes. Smoking, eating and drinking are prohibited in the workplace. After work, shower and change clothes. Store contaminated clothing separately and wash before use. Maintain good hygiene practices. The company recommends that all polyurethane catalysts be stored in a dry, cool and properly ventilated area. All storage containers must be well sealed to avoid contact with water or other affected substances, which may alter the performance of the product in use. The storage temperature is 10°C to 30°C. Lower or higher temperatures are inappropriate and should be avoided if possible.
Company Name: |
Newtop Chemical Materials (Shanghai) Co., Ltd. |
Sales Manager: |
Hunter |
E_Mail: |
[email protected] |
Telephone: |
86-021-5657 7831 |
Fax: |
86-021-5657 7830 |
Address: |
Rm. 1104, No. 258, Songxing West Road,
|
Website: |
www.newtopchem.com |
Dabco amine catalyst/amine balance catalyst
Dabco amine catalyst/amine balance catalyst
Overview:
Product Name: Dabco NE210
Alias: Dabco NE210, Amine Equilibrium Catalyst NE210, Equilibrium Catalyst NE210, Dabco Amine Catalyst, Non-Emitting Amine Catalyst, Amine Catalyst, Amine Equilibrium Catalyst
Product Description: Dabco NE210 is a solution of 30% ZF-10 and 70% NE1070.
Product Physical Properties:
Appearance: light yellow liquid
Viscosity (25℃,mPa.s): 320
Density (25℃,g/cm3): 1.03
Water solubility: soluble in water
Flash point (PMCC,℃): 134
Hydroxyl value (mgKOH/g): 620
Typical Physical Properties Table.
Appearance Colorless transparent liquid
Specific gravity 1.03
Viscosity@25℃ mPa.s 320
Water solubility @25°C Completely soluble
Flash point, ℃ 134
Product Usage:
Dabco NE210 is a non-emitting amine equilibrium catalyst that reacts into the polyurethane matrix and therefore produces no emissions;
Dabco NE210 is suitable for all molded foam and high density foam applications to meet OEM emission regulations such as VDA278;
Advantages of Dabco NE210 include: no amine catalyst emissions, no VOC emissions, no vinyl staining, no windshield fogging, and stable masterbatch;
Dabco NE210 can be used in any water-blown TDI or TDI/MDI high resilient foam (HR) as well as TDI/MDI or MDI-type cold cure molded polyurethane foam;
Dabco NE210 is recommended at a dosage of 0.50 to 1 PPHP (per hundred parts of polyol) in MDI systems and 0.40 to 0.70 PPHP in TDI systems.
DABCO NE210 polyurethane foaming catalyst is a new, second generation, non-emission (NE) foaming catalyst that chemically binds to the polyurethane foam matrix and maintains the foam properties of diphenylmethylene diisocyanate (MDI) or toluene diisocyanate (TDI) systems.
DABCO NE210 eliminates windshield fogging and polyethylene plastic contamination caused by odor and volatile emissions when used in automotive manufacturing. This catalyst can be used in combination with other non-volatile catalysts such as Dabco NE1070 or alone with conventional co-catalysts to reduce volatiles and odor emissions. The Dabco NE210 catalyst was shown to be free of volatile emissions by dynamic above surface gas analysis using standard automotive OEM VDA278 methodology. These results confirm that the catalyst is fully bonded to the foam matrix. Vapor pressure measurements show that the volatility of the catalyst is well below current industry standards, which means that catalyst processing in foam production lines is much less volatile.
Advantages of DABCO NE210:
-
No amine catalyst volatilization
2、No volatile organic compounds emission
3, no polyethylene plastic contamination
4, no windshield fog and water droplets
5, Batch-to-batch stability is guaranteed
Shelf life.
Keep unopened, two years
Storage and transportation:
Should be sealed and stored in a dry, cool and ventilated warehouse
Packaging:
200KG/drum Storage: it is recommended to store in dry and cool area with proper ventilation. Please fasten the packaging cover as soon as possible after the original packaging to prevent the mixing of other substances such as moisture and other substances that may affect the product performance. Store in a cool and dry place, keep the container sealed and avoid contact with oxides. Do not inhale dust and avoid contact with skin and mucous membranes. Smoking, eating and drinking are prohibited in the workplace. After work, shower and change clothes. Store contaminated clothing separately and wash before use. Maintain good hygiene practices. The company recommends that all polyurethane catalysts be stored in a dry, cool and properly ventilated area. All storage containers must be well sealed to avoid contact with water or other affected substances, which may alter the performance of the product in use. The storage temperature is 10°C to 30°C. Lower or higher temperatures are inappropriate and should be avoided if possible.
Company Name: |
Newtop Chemical Materials (Shanghai) Co., Ltd. |
Sales Manager: |
Hunter |
E_Mail: |
[email protected] |
Telephone: |
86-021-5657 7831 |
Fax: |
86-021-5657 7830 |
Address: |
Rm. 1104, No. 258, Songxing West Road,
|
Website: |
www.newtopchem.com |